Choose the warning shown on your machine. Check the model number and compare the full pattern with the manufacturer’s instructions before trying a fix.
Select your brand, then confirm the exact model and full code or light pattern. Indicator lights can change meaning when they flash instead of staying on. This database distinguishes manufacturer-documented meanings from possible causes; it does not diagnose an internal component from a display alone.
Philips
3200 LatteGo
Check the rating label and model revision before following a repair or reset procedure.
Displayed code
Error 01
What it means
Philips associates code 01 with a blocked coffee funnel/grinder feed. Check that your specific 3200 control panel actually displays this numeric code.
Possible causes
- Ground coffee obstructs the accessible funnel.
- Oily beans or moisture may contribute to a recurring blockage.
What you can check yourself
- Switch off fully and allow the machine to stop.
- Remove the brew group as instructed and inspect the accessible funnel.
Diagnostic sequence
- Wait about 15–20 seconds after switching off.
- Remove the brew group and clear accessible dry grounds as the manufacturer instructs.
- Reassemble, restart once and observe whether the code returns.
When to contact service
Contact Philips if the code persists after the documented cleaning; do not pour water into the bean container.
Manufacturer source / model support · Detailed guide · Diagnose this model
Displayed code
Error 03
What it means
Philips defines 03 as a brew group that is too dirty, on compatible displays.
Possible causes
- Coffee residue obstructs normal brew group movement.
- A missed cleaning cycle may allow grounds to build up.
What you can check yourself
- Confirm the display says 03.
- Let the machine shut down before removing the brew group.
Diagnostic sequence
- Remove the brew group using the model manual.
- Rinse it with lukewarm water and allow it to air dry.
- Reinsert without force and restart once.
When to contact service
Contact Philips if the group cannot be removed safely or 03 persists after cleaning.
Displayed code
Error 04
What it means
Philips defines 04 as a brew group that is not correctly positioned, on compatible displays.
Possible causes
- The group was not fully reinserted.
- It may be out of its normal position after an interrupted shutdown.
What you can check yourself
- Confirm the display says 04.
- Check whether the group clicks into place without force.
Diagnostic sequence
- Switch off normally and wait until movement stops.
- Align the brew group in its neutral position as the manual shows.
- Reinsert until it clicks, close the door and restart once.
When to contact service
Contact Philips if the group will not seat without force or 04 continues.
Displayed code
Error 05
What it means
Philips associates 05 with air trapped in the water circuit on compatible machines.
Possible causes
- Air entered after an empty tank or filter replacement.
- A filter may not have been primed or fitted correctly.
What you can check yourself
- Fill and firmly fit the water tank.
- If an AquaClean filter was just installed, check its preparation instructions.
Diagnostic sequence
- Switch off normally and remove the AquaClean filter if fitted.
- Fill the tank and dispense 2–3 cups of hot water per Philips guidance.
- Prepare the filter as instructed before refitting it.
When to contact service
Seek Philips support if hot water cannot be dispensed or code 05 continues after the official air-removal procedure.
Manufacturer source / model support · Detailed guide · Diagnose this model
Displayed code
Error 14
What it means
Philips identifies error 14 as an overheated machine on models that display this code. Confirm that your exact 3200 variant shows 14.
Possible causes
- The machine temperature has exceeded its operating range.
- If the error returns after cooling, an internal temperature-control fault is possible but not confirmed.
What you can check yourself
- Read the exact displayed number and stop brewing.
- Check whether the appliance feels unusually hot or has a burning smell without opening it.
Diagnostic sequence
- Switch off using the normal control.
- Allow the machine to cool for 30 minutes, as Philips instructs.
- Restart once and check whether the code has cleared.
When to contact service
Leave it off and contact Philips if 14 returns after cooling, a burning smell appears, or the machine cannot restart safely.
Reviewed September 2026. Verify the manual for the exact model and market. Turn off and unplug when safe if you notice smoke, a burning smell or water near electrical parts. Never force a stuck brew group.